People use automatic doors daily, yet we are only aware of their presence when they malfunction. They’re quite useful, which is why they’re so popular.
They are, however, relatively costly, and if something goes wrong, you can expect a large charge. Unfortunately, avoiding paying for the repairs is impossible.
After all, every electrically powered equipment eventually begins to show symptoms of wear and tear. This technology isn’t infallible, but it can be made to endure longer.
It makes sense to keep up with routine maintenance once you’ve invested in high-quality automatic doors. Maintaining your power door system with routine maintenance and safety checks will help it last longer.
To get the most out of your investment in low-energy operators, make sure your door system is functioning properly.
How to maintain
Legislation is increasingly regulating the control and maintenance of automatic doors. Regardless, you can contact your service firm as soon as your automated doors give you a warning that they are about to break down.
Following are some of how you can maintain automatic doors:
- Lubrication
- Keep water out of the seal and the channel
- Keep an eye out for insects
- Check the electrical panel regularly
- Clean the area around the automated door
- Every two months, grease the doors
- Examine the state of the door springs
- Inspect the door panels for any damage
- Consider purchasing an extended warranty
Lubrication
You should first rule out the possibility of broken parts causing the squeaking. To avoid noise and wear issues, inspect the friction systems such as hinges, locks, and latches. Where the motor and the door spin, they are the important points to grease.
However, the arms, chains, counterweights, and zippers of the doors, if any, you should not avoid. If these places remain greased and do not dry, your automated door will have to operate more smoothly, as we previously stated.
Tip
A door grease could be oil or a thin layer of petroleum jelly, but the latter is preferable since it is more lasting, light, and does not harden.
Keep water out of the seal and the channel
Rain and humidity sometimes cause damage to the control panels of automated doors in several instances. If it’s mounted on the wall, make sure water doesn’t get in through the screw holes or the cable entry.
If this does happen, it’s a good idea to sell these door spaces with silicone.
Keep an eye out for insects
Why should insects or other tiny creatures be harmed if water has entered the control box? This happens due to the current transformer by the heat it produces.
This issue is especially common in automatic sliding door motors. Because they install at ground level, making them more accessible. And if the cable entry has been left open below, it becomes worse.
Tip
Although you should be very cautious if there are children or pets in the area. However, you should seal the entry or place mouse poison in the area near the engine. Watch out for roaches and ants!
Check the electrical panel regularly
When the motor runs, check to see whether any relays have any burns by their frequent use, but don’t touch them. If you have the know-how of the electronics, you can look for damage to other door parts.
Perhaps, you can ask for a replacement for your automatic door or contact a repair service before the problem worsens.
Clean the area around the automated door
Garbage and dust might gather to varying degrees depending on the sort of automatic door you have placed in your home or office.
We must keep the floor guides where the sheets run clean on sliding doors. As they might cause jams or even door derailment, which is quite dangerous.
Tip
Look for the garbage as it can build where the hinges are on the doors. Depending on the type of hinge and installation, it causes the automatic door to not close properly.
Every two months, grease the doors
This is one of the steps we advise clients to take if they want to drastically minimize the number of times their doors break down. In these circumstances, the constant grease may not be sufficient because it can develop blockages over time.
Spray grease, which is available at any hardware shop, works great in these situations. The areas on the sliding doors that require oil are those that allow the motor and door to turn smoothly.
Tip
Do not unscrew the motor and thicken the interior because it has already been lubricated during construction to prevent dirt from getting into it.
Examine the state of the door springs
As the springs extend to close the door and contract to open it, they can corrode and lose strength over time. Spring breakage is normal. Add oil to the springs and check that they have not lost tension and may adjust again.
Inspect the door panels for any damage
If the door is sectional and automated, inspect the panels for dents on the surface. It is important to contact professionals who have experience with all types of doors to replace the panel.
It is not an expensive chore to maintain an automated door, but it is preferable to avoid difficulties.
Consider purchasing an extended warranty
If you’re installing a new automated door, ask for a warranty extension. It doesn’t matter if you know how to maintain it or are completely new to this – it’s your best choice for peace of mind if the door breaks down for any reason.
Furthermore, request a warranty on individual parts from the installer. No one can be fully sure. Perhaps, it’s better to be ready for something worse than to pay a lot more when you can simply avoid it.
Conclusion
To conclude, having an automatic door is convenient, but paying for repairs is not. While it’s hard to avoid having to make repairs at some time, there are a few things you can do to keep the costs down.
Whether it’s a sliding door or an automatic swing door, no one wants to pay a high price for not paying attention and maintaining it. Perhaps, try doing so regularly rather than only when it breaks down.
